Brake Hardware

Convenient set of four or part # 310-3634, CLIP,RETAINING,PIN for DP6, D8, TX6 and Aero calipers.

Rotor and Hat Register Adapters are used to locate 1 piece iron rotors and aluminum hat assemblies to vehicle specific hub or axle registers. Available in size ranges from 2.00” to 2.88” internal diameter. Requires 3.06” center hole with counter bore for installation into...

Stop Light Pressure Switch, dual pole with a 1/8th pipe male inlet. Circuit turns on at 60-100 psi. Used in part #260-11179 Combination Proportioning Valve assembly. Plated steel construction.

This valve can be used as a brake shut-off. When energized, the valve will block pressure from reaching downstream. The valve does not prevent fluid from returning to the master cylinder. This eliminates the possibility of trapping pressure when activating the valve. Requires a...

The new generation of adjustable proportioning valves combines the latest refinements to deliver precise pressure metering and strength from a compact forged billet design. Pressure adjustments range from 100-1000 PSI and provide for a maximum decrease of 57% in line pressure, the most of...

The new generation of adjustable proportioning valves combines the latest refinements to deliver precise pressure metering and strength from a compact forged billet design. Pressure adjustments range from 100-1000 PSI and provide for a maximum decrease of 57% in line pressure, the most of...

Wilwood Quick Disconnect Kit -3 AN

Wilwood Brake Bleed Bottle w/ Tubing

Wilwood finally has an elegant answer to the question, “Where do I mount my Combination Proportioning Valve1/4” with their new Mounting Bracket Kit. • Specifically designed to work in conjunction with Wilwood Aluminum Tandem Master Cylinders (P/N’s 260-8555, 260-8556, 260-9439, 260-12900 or 260-13375), in...

Wilwood finally has an elegant answer to the question, “Where do I mount my Combination Proportioning Valve1/4” with their new Mounting Bracket Kit. Specifically designed to work in conjunction with Wilwood Remote Tandem Master Cylinders in manual or boosted system applications. Kit includes: Stainless...

Wilwood's two, four and ten pound residual pressure valves retain a minimum brake line pressure to help eliminate excessive pedal travel in both disc and drum brake systems. The two pound valve is used in disc brake applications where the master cylinder is mounted...

Wilwood's two, four and ten pound residual pressure valves retain a minimum brake line pressure to help eliminate excessive pedal travel in both disc and drum brake systems. The two pound valve is used in disc brake applications where the master cylinder is mounted...

Wilwood's two, four and ten pound residual pressure valves retain a minimum brake line pressure to help eliminate excessive pedal travel in both disc and drum brake systems. The two pound valve is used in disc brake applications where the master cylinder is mounted...

The new generation of adjustable proportioning valves combines the latest refinements to deliver precise pressure metering and strength from a compact forged billet design. Pressure adjustments range from 100-1000 PSI and provide for a maximum decrease of 57% in line pressure, the most of...

Wilwood's Master Cylinder Bench Bleeding kit contains all fittings and hoses to properly bench bleed your master cylinder, either tandem or single outlet. Bench bleeding is a necessary to assure that system is completely bled and free from trapped air.

Wilwood’s new Combination Proportioning Valve substantially simplifies mounting, plumbing, wiring and brake proportioning adjustments on vehicles with custom brake systems. The combination block maintains full isolation between front and rear fluid circuits and can be used in conjunction with any tandem outlet or dual...

The new generation of adjustable proportioning valves combines the latest refinements to deliver precise pressure metering and strength from a compact forged billet design. Pressure adjustments range from 100-1000 PSI and provide for a maximum decrease of 57% in line pressure, the most of...

This easy to read two inch diameter non-hazing face allows for quick brake line pressure checks from 0-1,500 PSI (or 0-10,000 kPa). 20 PSI graduations and accuracy to 1.5% permit reliable brake bias setup and brake system troubleshooting. It is durable and corrosion resistant.

Wilwood’s Lug Mount Front Bracket kits mounts Lug mount calipers with 5.25” center to center mount used in various Wilwood calipers. Mounts are application (vehicle) specific and contain 3/8-24 clinch nuts for caliper mounting. Engineered from high strength aluminum alloy.

Wilwood’s FSL6R bracket mounts the Forged Superlite Radial Mount calipers to 3.50” center to center lug mount. Mounting height is optimized to allow mounting this caliper in all applications that originally used Superlite series calipers. Brackets include studs, shim and the mounting hardware.